Kamyeklaf

Guide · DWG files

Quantity take-off directly from a DWG file: why quantities get lost in conversion to PDF and how to avoid it

A DWG file carries the drawing in its true units: every line has a length in millimetres, every element sits in a named layer, and every block has a name and a count. A PDF file carries a printed image of that drawing on a sheet of paper at a certain scale, and what was not printed does not survive. In conversion the layers are lost, the dimensions become a proportion of the paper size, and a single "fit to page" option is enough to change the scale by a ratio nobody knows. Take-off from DWG is more accurate and faster when the file is available, and take-off from PDF is possible provided the scale is verified on every sheet before the first measurement. This guide explains what is lost, how to check, and how each works on screen.

What a DWG file carries that a PDF does not

What is in the fileDWG / DXFPrinted PDF
Drawing unitReal (mm or m); a line of length 4000 means 4.00 mA proportion of the paper size; needs a scale to interpret
ScaleOne for the model space, plus output scales in the sheet viewportsOne per sheet as printed, and it may differ from sheet to sheet
LayersPresent with their names (walls, doors, dimensions, text)Dissolved into one image
BlocksA repeated element with a name and a count, counted programmaticallyRepeated shapes counted by eye
Text and dimensionsReadable text linked to the elementPrinted text, which may turn into corrupted symbols if the Arabic fonts are not embedded
Closed areasPolylines with a computed areaBoundaries that must be redrawn
What lies outside the print frameSavedNot present

The essential difference is that DWG describes things and PDF describes Sheet. Whoever takes off from DWG asks the file: how long is this wall? Whoever takes off from PDF asks: how long is this line on the paper, and by what scale do I multiply it? The second question admits an error the first does not.

Where quantities get lost in conversion

1. "Fit to page" ruins the scale

The most frequent mistake. The sheet is drawn for A1 at 1:100, and the office exports it to PDF on A3 with the fit-to-page option, so it shrinks by roughly 50%, but the actual ratio depends on the printer margins. The engineer reads "1:100" in the title block and measures with it, so lengths come out at half their value and areas at a quarter. The error shows only when a written dimension is compared.

2. A different scale for every sheet in the same file

A 20-sheet PDF may contain plans at 1:100, details at 1:20 and sections at 1:50, and some sheets have two viewports at two scales. Whoever sets one scale for the whole file is wrong on every sheet that differs from it.

3. Layers dissolve

In DWG you can hide the furniture, dimension and text layers and leave the walls alone, so the blockwork is measured without clutter. In PDF everything is in one image, so a furniture line is counted as a wall, or a label hides an important dimension.

4. Blocks become drawings

A door in DWG is a block named, say, D1 that can be counted with one command across the whole file. In PDF it is an arc and a line counted by eye sheet by sheet, and visual counting is a permanent source of dispute. In a published test of a twin villa, the only item flagged "Review" among the examples shown was a count of doors from the sheet's symbols rather than from a schedule, and that is exactly what happens with PDF.

5. Arabic text gets corrupted

Arabic fonts not embedded in the PDF turn into boxes or random Latin letters when read as text. In an electrical bill of quantities exported from Excel, the Arabic letters were corrupted symbols when read as text, and its 57 items were read correctly only by reading the page as printed. In DWG the text is stored in its encoding and is not corrupted by printing.

6. What lies outside the frame is dropped

The designer's notes, auxiliary schedules and details placed beside the sheet in model space that did not enter the print frame never reach the PDF.

When PDF is all you have

Often. The owner sends what they have, the engineering office does not hand DWG to contractors before the contract to protect its rights, and old projects may survive only in print. Take-off from PDF is not a mistake but work with its conditions:

  1. Verify the scale on every sheet by measuring a written dimension (a room length, or the distance between two column axes) and calibrating the scale to it, not to what is written in the title block.
  2. Check both directions: measure one horizontal and one vertical dimension, as some conversions distort the aspect ratio.
  3. Prefer written dimensions over measured lengths wherever they exist. The figure printed by the designer is more reliable than your measurement on an image.
  4. Heights from the sections , not the elevations, as in the guide to take-off mistakes.
  5. Ask for the DWG for the next stage: after the contract the contractor is entitled to ask for the original files for more accurate execution, and many offices hand them over then.

Example: one wall both ways

An external wall in a test villa with a true length of 12.40 m and a height of 3.30 m.

MethodWhat happensResult
From DWGThe line is 12400 drawing units long, and the unit is mm12.40 m × 3.30 = 40.92 m²
From a PDF at the title-block scale 1:100 on A1, printed correctlyLine length on paper 124 mm × 10012.40 m × 3.30 = 40.92 m²
From the same PDF exported "fit to page" to A3 (0.70 reduction assumed)Line length on paper 86.8 mm × 1008.68 m × 3.30 = 28.64 m², 30% short
From the PDF after calibrating the scale against a written dimensionCalibration reveals the actual scale is 1:14312.40 m × 3.30 = 40.92 m²

The third row is what happens in many offices every day, and the fourth row is the minute that prevents it. The 0.70 reduction is an assumption for illustration; in reality it depends on the printer and its margins, which is why it cannot be corrected with a fixed factor.

Why DWG remains more accurate even with calibration

Calibration corrects the scale but does not bring back the layers, the blocks or the intact text. With DWG the engineer gets three things no PDF gives however it is processed:

And because DWG is a format owned by Autodesk, reading it outside AutoCAD goes through specialised libraries such as those published by the Open Design Alliance, or through the open exchange format DXF which Autodesk documents publicly and every drawing program exports. PDF, on the other hand, is the standard ISO 32000 designed to fix the appearance of the printed page, which is exactly what makes it excellent for delivery and weak for measurement.

What this looks like on screen

KAM Estimator opens DWG and DXF directly without an external tool: the file is converted into sheets on your computer by a built-in tool, at its true scale, and the original file is not sent to any server. It opens a complete PDF of up to 25 MB and 40 sheets as printed, and accepts IFC and images. In both cases every sheet is read twice independently, and every item comes out with its sheet, its position and its calculation basis, so the scale and dimensions are reviewed from the bill itself. Whoever wants to measure by hand has manual take-off by drawing on the plan for both cases. The documented figures from the November 2026 tests are on the engineering offices page.

Checklist before the first measurement

References

  1. Autodesk: DXF Reference · The published DXF specification, the open exchange format, checked
  2. Open Design Alliance · Reading DWG outside AutoCAD, checked
  3. PDF Association: ISO 32000-2 · The PDF specification: what the printed page carries and what it does not, checked

FAQ

Can quantities be taken off accurately from a PDF?Yes, if the scale is calibrated against a written dimension on every sheet and the printed dimensions are preferred over measurement. The difference from DWG remains in layers, counting and text.
What is the difference between DWG and DXF?DWG is the original proprietary AutoCAD format; DXF is an open exchange format that Autodesk documents and every drawing program exports. Both carry the drawing with its units and layers; DXF is larger and easier to read outside AutoCAD.
Why do my quantities differ from the engineering office's with the same drawing?The first reason is usually the scale: one of the two took off from a PDF exported fit to page. Measure a written dimension together. The next reasons are deduction and waste rules.
Do I need AutoCAD to open a DWG for take-off?No. Take-off programs that read DWG directly open it without AutoCAD, and free DWG viewers display it. What matters is that the program reads the drawing unit and the layers, not an image of it.
Is the scale written in the sheet's title block reliable?Reliable for the original print only. Any re-export, scan or "fit to page" makes it invalid, which is why it is always calibrated against a written dimension.
What do I do if the Arabic letters in the PDF are corrupted?Read the page as an image, not as text. Visual reading of the page as printed bypasses the problem of unembedded fonts, and that is how an electrical bill of quantities with corrupted letters was read in full, all 57 items, in a published test.
Is the DWG file sent to a server when using the app?In KAM Estimator, no; the file is converted into sheets on your computer and the original is not sent to any server. What is sent when AI reading is requested is the page images and their text, and it is deleted from the server after the task, as the security and trust page details.

Try take-off from DWG

Open a DWG or DXF file as it is with its scale and layers, read the doors and windows from the drawing itself and their sizes from the sheet's schedule, and the file is converted on your computer with the original never sent to any server.

KAM Estimator desktop appTake-off from DWG video

This guide was published on . The prices mentioned are examples from published references with their dates, not a quotation.